CONCRETE SEALER RIVERTON | CANNING | PERTH | SEALING CONCRETE DRIVEWAYS, FLOORS & PAVERS (2023)

Building materials such as concrete are made up of countless invisible capillary pores that allow for the absorption of damaging liquids such as water, water-borne salts and oils. These liquids cause concrete to deteriorate prematurely and in doing so reduce its usefulness. Examples of deterioration include; unsightly staining, weathering, loss of strength, efflorescence, salt attack, sulphate attack, biological attack, chemical attack, swelling, embrittlement and picture framing. Sealing your concrete will help eliminate or significantly reduce most of these problems.

Deepshield™will not affect the slipperiness of concrete surfaces and does not cause any yellowing or leave a visible shine. Deepshield™ is suitable both indoors and outdoors and is ideal for use around swimming pools and other wet areas.

An easy way to find out if your concrete is sealed, is to carry out a water test. Place a tablespoon of water on the treated surface for 20 minutes, remove the water with a tissue or cloth, pressing hard to soak up any water in the texture of the surface. If the water is absorbed or leaves a dark mark, and the concrete needs to be sealed, otherwise, the surface is adequately sealed and does not require further sealing.

Highly polished surfaces and dense materials have extremely fine micro pores that require a specific formula to penetrate. Deepshield™ GOLD is based on the latest fluoro-bond technology and designed to penetrate and chemically bond to the micro pores of dense surfaces, providing protection for up to 15 years. Both Deepshield™ GOLD and Deepshield™ Transparent Penetrating Sealer provide the highest level of protection against water and oil based stains without altering the surface texture or appearance.

Concrete has a porous internal structure. Moisture present in the ground can be wicked or drawn up into concrete by capillary action. If natural vapour transmission is not allowed to take place, moisture gets trapped and can cause chemical and physical changes within the material. This action of decay can take the form of pitting, spalling, flaking and oxidation.

Topical sealers produce a physical barrier over concrete which also results in a darkening, yellowing or glossy coating. Surface sealers (topical) usually don't last as long, can make the floors slippery and need to be completely removed the next time sealing is required. Salts and efflorescence may also build-up under the non-breathable surface, causing the coating to appear cloudy.

No. Deepshield™ provides a preventive measure that gives extra protection to concrete, which still needs to be maintained once sealed. Deepshield™ will last longer and work better when the concrete is properly cared for. In addition, periodic professional maintenance such as cleaning, polishing and repairs are definitely recommended.

As Deepshield™ doesn't alter the appearance of the concrete, you wont be able to check just by looking at the surface. The easiest way to measure the strength of the seal is to apply a teaspoon of water to the surface and see if the colour beneath the water darkens after a few minutes. If the concrete darkens, that means that moisture has penetrated, and a fresh coat should be applied.

Deepshield™ Transparent Penetrating Sealer protects concrete for up to 10 years from both water and oil based contaminants. If you sealed your concrete with Deepshield™ GOLD and have properly maintained your surfaces the sealer should last up to 15 years. The longevity can vary depending on the type of concrete, the location and what type of wear the surface is exposed to.

To keep your concrete looking new, it is recommended cleaning each week using a pH neutral cleaner to remove any dirt or grime. Strong detergents (strong acid or alkali) may affect the sealer. Mild detergents and pH neutral substances are strongly recommended.

No. Deepshield™ will penetrate the concrete and bond to the pore structure. It is not a surface coating and will not crack, peel, yellow or discolour at any time.

All Deepshield™ products are available from our online store, or from one of the dozens of Accredited Applicators throughout the country. Please refer to our “Online Shop” section for further details.

Deepshield™sealers should be applied liberally, using a low-pressure sprayer, lambswool applicator, bristle broom, paintbrush or roller. Whatever suits you best!

Every surface is subtlety different. Unless you have applied the sealer to the exact same surface with the same conditions as before, it is vital to conduct a small trial to ensure you get the result you are after.

All Deepshield™ products are non-toxic and safe for use in food preparation areas.

No sealer can prevent all stains all the time. The sooner any spill can be cleaned the less likely a stain will result. Clean your concrete surface regularly so dirt and stains don't have a chance to build up.

Pre-existing surface sealers (topical) must be removed before applying Deepshield™ as the coating left by the old sealer may block the product from penetrating the surface. You don't however need to strip pre-existing penetrating impregnating sealers, as Deepshield™ will pass through previously applied impregnating sealer.

Deepshield™ do not recommend this due to possible bond and/or aesthetic issues, however if you choose to apply a topical sealer over a concrete surface treated with Deepshield™ please first carry out a test on a sample area to determine the result.

The straight answer is no. Deepshield™dries invisible, sealing the pores within the concretes surface without changing the feel, texture or colour. The only exception to this is Deepshield™ Colour Enhancing Penetrating Sealer, which will slightly darken and highlight the character, providing a wet look, without altering the surface texture.